A Satisfactory Luting Mixture
: CASE-HARDENING OR SURFACE-CARBURIZING: The Working Of Steel
A mixture of fireclay and sand will be found very satisfactory
for closing up the boxes, and by observing the appearance of the
work when taken out we can gage the suitability of the methods
employed, for unless the boxes are carefully sealed the work is
generally covered with dark scales, while if properly done the
articles will be of a light gray.
By observing the above recommendations reliable results can be obtained,
and we can expect uniform results after quenching.
More
-
A Chromium-cobalt Steel
The Latrobe Steel Company make a high-speed steel without tungsten, its red-hardness properties depending on chromium and cobalt instead of tungsten. It is known as P. R. K-33 steel. It does not require the high temperature of the tungsten steels, h... A Satisfactory Luting Mixture
A mixture of fireclay and sand will be found very satisfactory for closing up the boxes, and by observing the appearance of the work when taken out we can gage the suitability of the methods employed, for unless the boxes are carefully sealed the wo... Affinity Of Nickel Steel For Carbon
The carbon- and nickel-steel gears are carburized separately owing to the difference in time necessary for their carburization. Practically all printed information on the subject is to the effect that nickel steel takes longer to carburize than pla... Air-hardening Steels
These steels are recommended for boring, turning and planing where the cost of high-speed seems excessive. They are also recommended for hard wood knives, for roughing and finishing bronze and brass, and for hot bolt forging dies. This steel cannot... Alloying Elements
Commercial steels of even the simplest types are therefore primarily alloys of iron and carbon. Impurities and their remedies are always present: sulphur, phosphorus, silicon and manganese--to say nothing of oxygen, nitrogen and carbon oxide gases,... An Automatic Temperature Control Pyrometer
Automatic temperature control instruments are similar to the Brown indicating high resistance pyrometer with the exception that the pointer is depressed at intervals of every 10 sec. upon contact-making devices. No current passes through the pointer... Annealing
ANNEALING can be done by heating to temperatures ranging from 1,290 to 1,380 deg.F. and cooling in air or quenching in water or oil. After this treatment the forgings will have a hardness of about 200 Brinell and a tensile strength of 100,000 to 112... Annealing
There is no mystery or secret about the proper annealing of different steels, but in order to secure the best results it is absolutely necessary for the operator to know the kind of steel which is to be annealed. The annealing of steel is primarily ... Annealing Alloy Steel
The term alloy steel, from the steel maker's point of view, refers largely to nickel and chromium steel or a combination of both. These steels are manufactured very largely by the open-hearth process, although chromium steels are also a crucible pro... Annealing In Bone
Steel and cast iron may both be annealed in granulated bone. Pack the work the same as for case-hardening except that it is not necessary to keep the pieces away from each other. Pack with bone that has been used until it is nearly white. Heat as ho... Annealing Method
Forgings which are too hard to machine are put in pots with a little charcoal to cause a reducing atmosphere and to prevent scale. The covers are then luted on and the pots placed in the furnace. Carbon steel from 15 to 25 points is annealed at 1,6... Annealing Of High-speed Steel
For annealing high-speed steel, some makers recommend using ground mica, charcoal, lime, fine dry ashes or lake sand as a packing in the annealing boxes. Mixtures of one part charcoal, one part lime and three parts of sand are also suggested, or two... Annealing Of Rifle Components At Springfield Armory
In general, all forgings of the components of the arms manufactured at the Armory and all forgings for other ordnance establishments are packed in charcoal, lime or suitable material and annealed before being transferred from the forge shop. Exce... Annealing To Relieve Internal Stresses
Work quenched from a high temperature and not afterward tempered will, if complex in shape, contain many internal stresses which may later cause it to break. They may be eased off by slight heating without materially lessening the hardness of the pi... Annealing Work
With the exception of several of the higher types of alloy steels, where the percentages of special elements run quite high, which causes a slight air-hardening action, the carburizing steels are soft enough for machining when air cooled from any t... Application Of Liberty Engine Materials To The Automotive Industry
The success of the Liberty engine program was an engineering achievement in which the science of metallurgy played an important part. The reasons for the use of certain materials and certain treatments for each part are given with recommendation...